Fissure Sealant Retention Trial (FSRT)
Split Mouth Clinical Trial of Fissure Sealant Retention With Self Etching and Total Etch Bonding Agent
調査の概要
状態
条件
詳細な説明
Pit and fissure sealant have been hailed as a highly effective preventive dental treatment since it was introduced first in late 1970s . Sealants have traditionally placed using two step bonding agents based on acid etching with phosphoric acid followed by drying and bonding agent application and curing. Multiple steps in application of bonding agents have been associated with more chances of procedure errors and prolonged procedure time. The newer bonding agents are based on minimizing the number of steps involved with introduction of self etching bonding agents.6th generation adhesives are based on mixing of two components where as the 7th generation adhesives are based on no mix technique.
Previous studies on fissure sealants have focused on conventional etch and rinse bonding agents, there are only few published studies on effectiveness of the self etch bonding agents in retention of fissure sealants in vivo that have targeted the 6th generation adhesive. Feigal and Quelhas reported equivocal results with use of self etching bonding agents in comparison with etch and rinse bonding agents, but their study was limited by smaller sample size. Similar study was conducted by Burbridge which was based on short clinical follow up of 6 month evaluation where Xeno III by Dentsply (6th generation bonding agent) was compared with Prime & Bond (Dentsply). Another study by Venker et al on Adper Prompt L Pop in a school sealant program was based on retrospective review of cases. In light of published literature on (6th generation) self etch bonding agent has been found to be equal or inferior to total etch bonding agents (5th generation). There are no published clinical trials on the retentiong rate comparison of total etch bonding agent with no mix slef etch bonding agents in pit and fissure sealant.
Our study is based on comparison of effectiveness of single step bonding agent (7th generation adhesives) versus two step bonding agent in fissure sealant retention.
研究の種類
入学 (予想される)
段階
- フェーズ2
- フェーズ 3
連絡先と場所
研究場所
-
-
Sindh
-
Karachi、Sindh、パキスタン、3500
- 募集
- The Aga Khan University Hospital
-
コンタクト：
- Nadia Aman, BDS
- 電話番号：5011 (92)214930051
- メール：nadia.aman@aku.edu
-
主任研究者：
- Nadia Aman, BDS
-
副調査官：
- Ali K Khuwaja, FCPS
-
副調査官：
- Farhan R Khan, FCPS
-
-
参加基準
適格基準
就学可能な年齢
健康ボランティアの受け入れ
受講資格のある性別
説明
Inclusion Criteria:
- Fully erupted bilateral first or second permanent molar teeth.
- Patients requiring fissure sealant due high caries risk.
- Age group 6-25 years.
- Occlusal fissures of molar teeth.
Exclusion Criteria:
- Cases where one of the molar on either side is grossly carious or restored
- Third molars
- Uncooperative patients
- Molar teeth with antagonist tooth not present or extracted
- Mentally and physically handicapped patients
研究計画
研究はどのように設計されていますか？
デザインの詳細
- 主な目的：防止
- 割り当て：ランダム化
- 介入モデル：階乗代入
- マスキング：ダブル
武器と介入
参加者グループ / アーム |
介入・治療 |
|---|---|
|
アクティブコンパレータ：1
application of total etch bonding agent ( 5th generation) for placement of resing based pit and fissure sealants.
|
Selected teeth would receive prophylaxis with pumice using prophylaxis brushes for 20 seconds. The teeth will be isolated with cotton rolls before application of bonding agent. The tooth selected for etch and rinse bonding system (two step bonding agent) will be treated with 37% phosphoric acid (Total Etch Ivoclar Vivadent) for 15 seconds followed by rinsing for 30 seconds and then drying with air syringe till frosty white appearance is achieved. Adper Single Bond 2 (3M ESPE) will be applied to occlusal fissure using applicator brushes followed by curing for 10 seconds. Clinpro(3M ESPE) fissure sealant will be applied to pits and fissures and then light cured for 20 seconds.
他の名前：
|
|
実験的：2
Self etch bonding agent (7th generation) application for placement of resin based pit and fissure sealant
|
For teeth selected for application of self etching bonding agent (Adper Easy Bond 3 M), the bonding agent will be applied to occlusal surface with microbrushes and will be left undisturbed for 20 seconds followed by air drying for 5 seconds and then will be light cured for 10 seconds.
Fissure sealant (Clinpro 3M ESPE) will be applied in a similar manner as for etch and rinse group and light cured.
他の名前：
|
この研究は何を測定していますか？
主要な結果の測定
結果測定 |
時間枠 |
|---|---|
|
fissure sealant loss
時間枠：3months
|
3months
|
二次結果の測定
結果測定 |
時間枠 |
|---|---|
|
fissure sealant loss
時間枠：6months
|
6months
|
協力者と研究者
スポンサー
捜査官
- 主任研究者：Nadia Aman, BDS、The Aga Khan University Hospital
研究記録日
主要日程の研究
研究開始
一次修了 (予想される)
研究の完了 (予想される)
試験登録日
最初に提出
QC基準を満たした最初の提出物
最初の投稿 (見積もり)
学習記録の更新
投稿された最後の更新 (見積もり)
QC基準を満たした最後の更新が送信されました
最終確認日
詳しくは
本研究に関する用語
キーワード
その他の研究ID番号
- 07GS028SUR
この情報は、Web サイト clinicaltrials.gov から変更なしで直接取得したものです。研究の詳細を変更、削除、または更新するリクエストがある場合は、register@clinicaltrials.gov。 までご連絡ください。 clinicaltrials.gov に変更が加えられるとすぐに、ウェブサイトでも自動的に更新されます。