Clinical Evaluation of 3D-Printed Versus Direct Composite Restorations in Class II Cavities
The aim of this study is to clinically evaluate the performance of 3D-printed composites compared to direct conventional composite restorations in Class II cavities
Studienübersicht
Status
Status
Bedingungen
Bedingungen
Intervention / Behandlung
Intervention / Behandlung
Detaillierte Beschreibung
Resin-based composites are widely used for posterior restorations because of their esthetics, adhesion, and conservative preparation. However, Class II restorations remain challenging due to polymerization shrinkage, marginal gaps, postoperative sensitivity, and inadequate proximal contacts. Digital additive manufacturing has emerged as a promising approach, offering precise fabrication, reduced material waste, and customizable restorations. Although laboratory studies suggest favorable mechanical properties and marginal adaptation, clinical evidence for 3D-printed intracoronal restorations remains limited. Therefore, this randomized clinical trial will compare the clinical performance of 3D-printed composite inlays with conventional direct composite restorations in Class II cavities over 24 months.
Studientyp
Studientyp
Einschreibung (Geschätzt)
Einschreibung
Phase
Phase
- Unzutreffend
Kontakte und Standorte
Studienorte
-
-
Egypt
-
Tanta, Egypt, Ägypten, 31511
- aculty of Dentistry, Tanta University, Tanta, Tanta 31527
-
-
Teilnahmekriterien
Zulassungskriterien
Zulassungskriterien
Studienberechtigtes Alter
Akzeptiert gesunde Freiwillige
Studienberechtigte Geschlechter
Beschreibung
Inclusion Criteria:
- Have at least two Class II carious lesions corresponded to ICDAS scores 4 and 5, representing dentinal caries suitable for operative restorative treatment.
- The absence of ongoing orthodontic treatment or use of prostheses.
- Good general health without relevant disease.
Exclusion Criteria:
- Uncooperative patient.
- Any parafunctional habits such as tooth clenching or grinding.
- Chronic pulmonary diseases and blocked nasal passages.
Studienplan
Wie ist die Studie aufgebaut?
Designdetails
- Hauptzweck: Sonstiges
- Zuteilung: Zufällig
- Interventionsmodell: Parallele Zuordnung
- Maskierung: Doppelt
Anzahl der Arme
Waffen und Interventionen
Teilnehmergruppe / ArmTeilnehmergruppe / Arm |
Intervention / BehandlungIntervention / Behandlung |
|---|---|
|
Experimental: 3D-Printed Composite Inlays
Participants will receive Class II restorations fabricated from a commercially available 3D-printable permanent composite resin using a standardized digital workflow. The restorations will be adhesively bonded to the prepared cavities according to the manufacturer's instructions. |
Class II cavities will be restored with digitally designed and 3D-printed permanent composite inlays. The restorations will be post-cured and adhesively cemented according to the material manufacturer's recommendations |
|
Aktiver Komparator: Direct Composite Restorations
Participants will receive conventional direct Class II restorations using a commercially available resin-based composite. Restorations will be placed incrementally using a standardized adhesive protocol and light-curing procedure according to the manufacturer's recommendations. Both groups will be clinically evaluated at baseline and during the 18-month follow-up period using standardized clinical criteria. |
Class II cavities will be restored directly using a conventional light-cured resin-based composite placed with a standardized incremental technique and adhesive protocol |
Was misst die Studie?
Primäre Ergebnismessungen
Primäre Ergebnismessungen
Ergebnis Maßnahme |
Maßnahmenbeschreibung |
Zeitfenster |
|---|---|---|
|
Fracture and retention
Zeitfenster: 18 months
|
Description: Clinical evaluation of fracture and retentin was conducted in accordance with the World Dental Federation (FDI) criteria by two calibrated examiners at baseline and after 6, 12, and 18 months. Each restoration was evaluated according to the degree of conformity with the established criteria as follows: score 1, excellent; scores 2 and 3, satisfactory; and scores 4 and 5, inadequate. Scores of 1-3 were considered indicative of clinical success, whereas scores of 4 or 5 were considered indicative of failure. |
18 months
|
Mitarbeiter und Ermittler
Sponsor
Sponsor
Publikationen und hilfreiche Links
Allgemeine Veröffentlichungen
- Balestra D, Lowther M, Goracci C, Mandurino M, Cortili S, Paolone G, Louca C, Vichi A. 3D Printed Materials for Permanent Restorations in Indirect Restorative and Prosthetic Dentistry: A Critical Review of the Literature. Materials (Basel). 2024 Mar 18;17(6):1380. doi: 10.3390/ma17061380.
- Duarte S Jr, Phark JH. Advances in Dental Restorations: A Comprehensive Review of Machinable and 3D-Printed Ceramic-Reinforced Composites. J Esthet Restor Dent. 2025 Jan;37(1):257-276. doi: 10.1111/jerd.13371. Epub 2024 Nov 18.
- Tanaka LEB, da Silva Rodrigues C, Grangeiro MTV, Campos TMB, de Melo RM. Characterization of 3D printed composite for final dental restorations. Clin Oral Investig. 2024 Oct 31;28(11):617. doi: 10.1007/s00784-024-06003-8.
- Peskersoy C, Oguzhan A. Evaluation of the Mechanical and Adhesion Characteristics of Indirect Restorations Manufactured with Three-Dimensional Printing. Polymers (Basel). 2024 Feb 23;16(5):613. doi: 10.3390/polym16050613.
Studienaufzeichnungsdaten
Haupttermine studieren
Studienbeginn (Tatsächlich)
Studienbeginn
Primärer Abschluss (Geschätzt)
Primärer Abschluss
Studienabschluss (Geschätzt)
Studienabschluss
Studienanmeldedaten
Zuerst eingereicht
Zuerst eingereicht
Zuerst eingereicht, das die QC-Kriterien erfüllt hat
Zuerst eingereicht, das die QC-Kriterien erfüllt hat
Zuerst gepostet (Tatsächlich)
Zuerst gepostet
Studienaufzeichnungsaktualisierungen
Letztes Update gepostet (Tatsächlich)
Letztes Update gepostet
Letztes eingereichtes Update, das die QC-Kriterien erfüllt
Letztes eingereichtes Update, das die QC-Kriterien erfüllt
Zuletzt verifiziert
Zuletzt verifiziert
Mehr Informationen
Begriffe im Zusammenhang mit dieser Studie
Schlüsselwörter
Andere Studien-ID-Nummern
Andere Studien-ID-Nummern
- 3D-Printed & Direct Composite
Plan für individuelle Teilnehmerdaten (IPD)
Planen Sie, individuelle Teilnehmerdaten (IPD) zu teilen?
Arzneimittel- und Geräteinformationen, Studienunterlagen
Studiert ein von der US-amerikanischen FDA reguliertes Arzneimittelprodukt
Studiert ein von der US-amerikanischen FDA reguliertes Geräteprodukt
Diese Informationen wurden ohne Änderungen direkt von der Website clinicaltrials.gov abgerufen. Wenn Sie Ihre Studiendaten ändern, entfernen oder aktualisieren möchten, wenden Sie sich bitte an register@clinicaltrials.gov. Sobald eine Änderung auf clinicaltrials.gov implementiert wird, wird diese automatisch auch auf unserer Website aktualisiert .